|
Q: What is RockSolid Floors® and why is it better than other floor sealing products?
A: RockSolid Floors® is a two-component product that when mixed together forms a 100% Polyurea floor sealer. RockSolid Floors® is superior to epoxies, urethanes, paints and other coatings. Polyureas form a harder, denser, more abrasion resistant film than any of them. RockSolid Floors® is superior to any other coatings because it is made from the most durable coating available – Polyurea.
Q: Is RockSolid Floors an epoxy?
A: No. RockSolid Floors® is a Polyurea based coating system.
Q: What is Polyurea?
A: If you’re familiar with Spray On Truck Bed Liners you’re familiar with Polyurea. RockSolid Floors® is formatted from the same family of products.
Q: Why is RockSolid Floors® more costly compared to epoxy?
A: Compared to other premium flooring products such as plastic tiles that start at $4 per sq ft. RockSolid is only .99 cents per sq ft. and unsurpassed durability over epoxy, being four times stronger. The kit also has a separate top coat included. Far surpassing the one thin coat that other systems sell.
Q: Will Steel wheels damage the floor when coated with RockSolid Floors?
A: RockSolid Floors® are resistant to steel wheels commonly used on floor jacks, engine hoists and even jack stands.
Q: What about gas, oil and brake fluid? Will these damage the RockSolid Floors?
A: RockSolid Floors® is impervious to gas, oil, salt and other harsh chemicals.
Q: Why do I need a protective coating on my garage floor?
A: Unprotected concrete floors will wear and be stained by oils and fluids. Damage can occur by the corrosive effects of snow and ice-melting chemicals such as rock salt. RockSolid Floors® coating system protects concrete from wear because it is actually harder and more durable than the concrete itself. RockSolid Floors® Polyurea is so dense that oils and fluids cannot penetrate its surface to soak in and cause staining. RockSolid Floors is impervious to the corrosive effects of rock salt. RockSolid Floors® beautifies your floor while prolonging the life of the concrete itself.
Q: Why does the floor have to be prepared for the RockSolid Floors® kit?
A: Floor preparation is crucial to the proper installation of RockSolid Floors®. The RockSolid Floors® coating system will not be able to penetrate and bond to concrete in areas where heavy oil or fluid contamination has occurred. To remedy these areas, use a full concentration of RockSolid Commercial Degreaser prior to etching the floor. The use of RockSolid Floors® Safe Etch Solution will help to remove some minor contaminants but it’s main purpose is to profile the concrete to provide an anchor for adhesion.
Q: Can I put RockSolid Floors® over pre-existing paints or other coatings?
A: While it is always best to apply RockSolid Floors® to freshly cleaned and etched concrete, the revolutionary Micro-Bond technology allows for RockSolid Floors® Polyurea to bond to previously coated floors. To do so, first check to guarantee that the existing coating is adhered to the floor. If so, you can simply sand the floor to etch the surface, clean it with a solvent and apply RockSolid Floors® primer body coat. If the existing coating seems to be delaminating from the surface or failing in any way, then it is recommended to remove it using mechanical means such as shot-blasting or diamond grinding prior to applying RockSolid Floors®.
Q: What is the purpose of the RockSolid Floors® decorative chip?
A: The decorative chip serves to enhance the appearance of the surface. Two different chip blends are included in each kit, allowing the customer to choose their decorative look. The two chip blends can also be combined for a truly original finish. The chip blends were chosen to accentuate the color of the floor and also provide a distraction to the naked eye – dirt and debris will be less visible.
Q: What will hot tires do to RockSolid Floors®?
A: Nothing. Tires heated from normal driving will not cause delamination the RockSolid Floors® finish.
Q: Do I have to recoat with RockSolid Floors® every year?
A: No, RockSolid Floors®’ hard, durable surface will last for many years under normal circumstances.
Q: Do I need to apply a clear coat over the RockSolid Floors® Coating?
A: The top coat is included with each kit comes with a limited lifetime warranty.
Q: Is the RockSolid Floors® coating slippery when wet?
A: No, the coating will not be slippery when wet. However if you wish to add an additional level of protection against slipping, you may add additional anti-slip aggregate like dry silica sand by broadcasting it in the topcoat during the application process.
Q: Can I get additional decorative chips for my RockSolid Floors® coating?
A: Yes, the RockSolid Floors® kit comes with a sufficient amount of decorative chip to complete a partial broadcast floor. Additional decorative chips are available for purchase at rocksolidfloors.com as well as full chip add on kits and extra top coat pouches.
Q: Will I be able to coat and/or apply the decorative chips to the vertical surfaces in my garage (stemwalls, curb, stairs)?
A: Yes, this is one of the many benefits of the RockSolid Floors® coating systems. Because our Polyurea primer / basecoat material is thicker and dries faster than any epoxy product available, coating of vertical surfaces, stairs, curb block, and sheetrock is a breeze. The coating will hold strong and not run down the vertical surface during curing. You will be able to broadcast chip onto to these surfaces to seamlessly match the floor!
|
|
Q: Can I get additional decorative chips for my RockSolid Floors® coating?
A: Yes, the RockSolid Floors® kit comes with a sufficient amount of decorative chip to complete a partial broadcast floor. Additional decorative chips are available for purchase at rocksolidfloors.com as well as full chip add on kits and extra top coat pouches.
Q: What are the decorative chips made of?
A: Our decorative chips are made of vinyl. Unlike other coating systems available who use acrylic chips, our vinyl chips are designed to lay down flatter, soak in better, and adhere better to the coating system. This leaves you with a flatter floor that the chips are embedded in, thus eliminating peeling or flaking over time.
Q: If my garage has windows, will the RockSolid Floors® coating fade or change colors?
A: No.
Q: Do I have to repair the cracks in my floor prior to installing RockSolid Floors®?
A: It is recommended that cracks be repaired prior to installing RockSolid Floors®. Repairing the cracks will not only improve the overall look of the floor but will help to keep contaminants, oil, grease, etc. from becoming trapped in the floor. Cracks need to be cleaned out and filled using RockSolid Floors® Fast Patch prior to coating.
Q: What are the average dry times for the RockSolid Floors® kit?
A: Foot traffic - 6-8 hours
Heavy traffic, moving items in - 8-12 hours
Vehicle traffic – 24 hours
Q: How do I clean my RockSolid Floors® coating if I stain it?
A: Stains wipe up with any standard cleaner / degreaser. RockSolid 24/7 Xtreme Green Clean is the recommended floor cleaner and will clean the majority of stains easily. This is available online a www.rocksolidfloors.com Tougher stains can be removed with mild automotive grade rubbing compound.
Q: Can I use a pressure washer to clean my RockSolid Floors® coating if needed?
A: Yes, pressure washing will not damage the integrity of the floor. Pressure wash at a low PSI.
Q: Why do we need a top coat.
A: RockSolid Floors® is a premium commercial grade system. The topcoat provides the ultimate protection against stains and normal wear and tear. A topcoat will also make cleaning the floor a breeze unlike other products on the market. Think of RockSolid Floors® topcoat like a clear coat for your car. The automotive industry doesn’t manufacture cars without a clear coat do they?
Q: How does the product stand up to snow and salt.
A: The company headquarters is in Minnesota and have been battle tested in the most adverse conditions. RockSolid Floors® is designed to be durable in all types of adverse conditions. The extra top coat which is included in each kit ensures that your floor is protected for years to come.
Q: Can I use this product on my shop floor?
A: Absolutely, this is the toughest coating system available and it has been used for years in heavy-duty industrial environments including Big Foot’s work shop. The world’s most recognizable monster truck.
Q: Why should I care about elongation?
A: All concrete moves and the number one failure of epoxy systems is its inability to bend or flex with the natural movements of concrete. Since Polyurea has an amazing ability to elongate or stretch it will bend and flex with the concrete thus resisting the cracking and peeling of other coating systems.
Q: Can I use your product in basements or inside spaces?
A: RockSolid Floors is an ideal choice for anywhere you want a flooring system that will last years and be impervious to water and household stains. Make sure that there is plenty of ventilation when installing this system in doors and extinguish all ignition sources.
Q: Can I use RockSolid Floors on my porch or sidewalk or exterior surfaces?
A: Yes, with the purchase of our Full-Chip Add On kit you can put RockSolid Floors on any exterior concrete or wood surface. Contact RockSolid Floors for installation tips at 1-866-765-4474
Q: Can I use RockSolid Floors in my work or play trailer?
A: Yes, this is a perfect use for RockSolid Floors Do-it-Yourself Kit. Our Polyurea will bond to any substrate other than plastic as long as the substrate is sanded or etched, vacuumed and given a solvent wipe. It is recommended that you purchase a full chip add-on kit for this installation as it will provide better hiding power for minor imperfections such as wood seams and screw holes.
Q: Will your product make a good Pick-Up bedliner?
A: Yes, with the purchase of our Full-Chip Add On kit you can put RockSolid Floors on any metal surface as long as the surface is first scuff sanded and wiped clean with acetone. For more installation tips please visit us on the web at www.rocksolidfloors.com or contact RockSolid Floors at 1-866-764-4474
Q: How do we get the full chip add on kit?
A: www.rocksolidfloors.com
Q: How do I clean my rollers and pan after the installation?
A: You cannot clean your rollers after installing the RockSolid product. However, extra material left in a plastic pan will not stick when its cured. You will simply be able to peel out any material to reuse the pan. For any installation you will need to have the following consumables:
(2) 9” or 18” rollers
(2) 9” or 18” roller pan
(1) 9” or 18” frame
(2) Disposable paint brushes
For more supplies needed look on the retail kit box or visit us on the web at www.rocksolidfloors.com |
